Best way to patch a nail hole in drywall

Gently pull the hammer out towards yourself away from the wall until the nail pops out. Tip: Save the nail in your toolbox in case you want to use it later. Pick up lightweight spackling to avoid harsh edges. Apply the lightweight spackle with a putty knife.

Open up the tub of wall spackle and dip the end of your putty knife into it. Grab a small glob of spackle that is just larger than the hole you want to fill. Place the putty knife right above the hole and drag it downward to apply the spackle, focusing on the hole with about 0.

Putty knives are flat, skinny tools made specifically for applying putty and spackling to walls. Smooth out the spackle with your putty knife. Drag the edge of the putty knife down around the edges of the hole to remove any unnecessary spackle. This will take the excess off your wall and make it easier to smooth out later.

Instead, stick to the outside edges. Wait 1 to 2 hours for the spackle to dry completely. Point a fan at your wall to speed up the drying process. Try not to touch the area until a few hours have passed so that the spackle has a chance to dry. Part 2. Sand the spackle slightly to remove the top layer. Use a fine grade sanding sponge or paper to slightly rough up the top layer of spackle.

Dampen a large sponge with warm water. Pick up a large, soft sponge used for grouting or tile work. Run it under the sink using warm water until the entire thing is wet, and then wring out the excess.

Rub the sponge over the spackle to take off the top layer. Swipe the sponge back and forth over the spackle on your wall until it disappears completely. Clean off the surrounding area of your wall if you notice any white dust from the sanding.

Dry off the area with a clean cloth. Finish off your wall by making the area look clean and dry with a cloth. Don't make repeated passes of the knife, as this can pull the joint compound from the hole.

Let the joint compound dry completely; with small holes, this usually takes less than one hour. And with very small holes, this single coat of joint compound is often enough to fill the hole smoothly. Joint compound shrinks slightly as it dries, so you will usually need to apply a second coat of mud with any hole that is larger than a small nail hole.

This is especially true if the hole is somewhat large, when cracks can often appear in the joint compound as it dries. When the first application is fully dry, apply more joint compound to the knife and apply a thin second coat over the hole.

This nearly always fixes any remaining pits and depressions. Allow this second coat to fully dry—at least one hour. Once the second coat is fully dry, run your hand over the patched area. If it feels rough, then use fine sandpaper or a fine sanding sponge to lightly sand the area and bring it flush with the surrounding drywall.

Make sure not to sand so aggressively that you damage the face paper. When patching screw holes in textured drywall, you will need to follow up by re-texturing the patch. Cans of spray-on texture are available that allow you to spot-texture sections of your wall. Actively scan device characteristics for identification. Use precise geolocation data. Select personalised content.

Create a personalised content profile. Measure ad performance. Select basic ads. Create a personalised ads profile. Select personalised ads. Apply market research to generate audience insights.

Let dry. Recommended Reading: Varisi Nail. The patch comes stuck to a 6-in. Everybody has a tube of toothpaste lying around. You can use toothpaste to fill small nail holes in your wall. Its the fastest way to get the job done. Toothpaste is a great quick fix if youre in a pinch. For example, you may have your landlord coming by in less than an hour to take a look around.

In that case, grab whatever you use to keep your teeth shiny and white. Its important to note that toothpaste eventually cracks as it dries.

Resultantly, its no good for filling larger holes, such as those accidentally made by a hammer. However, theres a trick that will eliminate this problem. Hopefully, you also have a few aspirins lying around. If so, crushed one or two aspirin and mix them with a small amount of toothpaste. The mixture will seal the hole and wont crack. All you need to do is apply the toothpaste to the hole, let it dry, and youre all set. Again, without painting, this quick fix method only works with white walls.

Also, it will only work with white toothpaste. If needed, a trip to the store for a small tube of white toothpaste is a lot easier than making your way to a hardware store. Recommended Reading: Hongo Cura Reviews. The process for how to fill nail holes that are a bit larger in size is pretty much the same as filling small nail holes, with the added caveat that youre probably going to want to add some reinforcement by means of adhesive-backed fiberglass mesh tape.

Heres how to do it:. If so, dont worry there are multiple ways, some easier than others, to fix the mistake and either make your hole smaller or fill the existing one completely to be able to make a new hole of the right size. In this article, you will learn about eight such methods that work mainly with wood. You will also learn what to do in case your hole is in metal or drywall.

If you really want to transform your rental into a space that feels more special, personalized, and stylish, you will most likely need to hang things on the wall. And while I have become a big fan of hole-less hanging via Command Strips in recent years, there are still some things that require nailing or screwing into drywall. This shouldnt stop you though because patching up drywall holes is quicker and easier than you might think.

Today, I want to show you how to fill nail holes in your walls using an easy, inexpensive all-in-one product. This tutorial is sure to come in handy whether youre getting ready to move out or you just made a mistake hanging your new art.

Lets get to it! Note: Use a 6-in. Let the compound dry, then sand lightly. Allow this first layer of joint compound to dry. Drying time may take up to two or three hours. You can speed up the joint compound drying time by ventilating the area and by keeping the room warm.

Once the joint compound is dry and solid, lightly sand down any high spots with a drywall sanding sponge.